Stair Parts, Molding, and Accessories


UT-25 ALL-IN-ONE URETHANE FLOORING ADHESIVE

Use Villagio’s UT-25 All-In-One Urethane Flooring Adhesive for all of your flooring and cork needs. UT-25 is a high-performance hardwood flooring adhesive that provides a tough, flexible, tenacious bond to a variety of surfaces, and it is not adversely affected by exposure to moisture, water, or alkalinity. UT-25 is an easy clean for before and after cure. This adhesive is used for residential, light commercial, heavy commercial, offices, and hospitals. UT-25 has ultra-low VOC and has NO formaldehyde. This flooring adhesive does not require moisture testing and provides unlimited moisture protection as well as sound control properties.

  • Volume: 4 Gallons
  • Material: Flooring Adhesive
  • Installation: Glue Down
  • Best Installed on the Following Substrates: Concrete, Plywood, OSB, Well Bonded Vinyl, Terrazzo, Ceramic Tile, Cement Backer Board, Gypsum Underlayment (dry, above-grade), and Cement Patch/Underlayment
  • Best Used with the Following Materials: Engineered Hardwood, Solid Hardwood, Bamboo, Cork, Parquet, and Plywood
  • Made in the USA

UT-25 can be removed from the surface of our flooring without mineral spirits or hard chemicals. You can simply scrape it off, once dried with a plastic scraper. If the glue has not dried yet, you can remove it with any California approved Urethane Adhesive Remover. 


UT-5 General Urethane Flooring Adhesive

Use Villagio’s UT-5 General Urethane Flooring Adhesive for all of your flooring and cork needs. UT-5 is a high-performance hardwood flooring adhesive that provides a tough, flexible, tenacious bond to a variety of surfaces. UT-5 is an easy clean for before and after cure. This adhesive is used for residential, light commercial, heavy commercial, offices, and hospitals. UT-5 has ultra-low VOC and has No formaldehyde. For first-floor installation slab and unlimited moisture protection check out our UT-25 All-In-One Urethane Adhesive.

  • Volume: 5 Gallons
  • Material: Flooring Adhesive
  • Installation: Glue Down
  • Best Installed on the Following Substrates: Concrete, Plywood, OSB, Well Bonded Vinyl, Terrazzo, Ceramic Tile, Cement Backer Board, Gypsum Underlayment (dry, above-grade), and Cement Patch/Underlayment
  • Best Used with the Following Materials: Engineered Hardwood, Solid Hardwood, Bamboo, Cork, Parquet, and Plywood
  • Made in the USA

UT-5 can be removed from the surface of our flooring without mineral spirits or hard chemicals. You can simply scrape it off, once dried with a plastic scraper. If the glue has not dried yet, you can remove it with any California approved Urethane Adhesive Remover.


T-MOLD

Villagio Hardwood T-Molding is used to connect and transition two rooms or types of floors professionally. The T-Molding also provides the proper connection between one rooms flooring to the next, such as under the door frame moving from carpet to hardwood. Please note that t-molding pieces are made-to-match, but cannot be “exact” matches. The t-molding pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces

Production time for this material is approximately 10 business days.

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 5/8″ Thick x 96″ Long x 2″ Wide
  • Material: Solid White European Oak T-Mold
  • Installation: Glue Down
  • Profile: 5/16″ thick Rounded Visible Transition

Some custom work will be accepted on a per request basis.


SOLID STAIR TREAD – SQUARE EDGE (NO LIP)

The Square Edge Stair Tread from Villagio is used to lay horizontally as one solid tread piece professionally.Please note that stair tread pieces are made-to-match, but cannot be “exact” matches. The stair tread pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces

Production time for this material is approximately 10 business days

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 1″ Thick x 96″ Long x 11-1/2″ Wide
  • Material: Solid White European Oak Stair Tread
  • Installation: Glue Down
  • Profile: Square Edge Solid One-piece Stair Tread with No Lip
  • Finish: Top and Square Edge Faces are Finished – All other sides are unfinished

Some custom work will be accepted on a per request basis.


SOLID STAIR TREAD – BULLNOSE (NO LIP)

The Bullnose Stair Tread is used to lay horizontally as one solid tread piece. Please note that stair tread pieces are made-to-match, but cannot be “exact” matches. The stair tread pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold per 8 ft. Pieces

Production time for this material is approximately 10 business days.

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 1″ Thick x 96″ Long x 11-3/4″ Wide
  • Material: Solid White European Oak Stair Tread
  • Installation: Glue Down
  • Profile: Rounded Solid One-piece Stair Tread (No Lip)
  • Top and Bullnose Faces are Finished – All other sides are unfinished

Some custom work will be accepted on a per request basis.


SOLID STAIR NOSE – SQUARE EDGE

The Stair Nose Molding is used to cap each hardwood step professionally. Please note that the stair nose pieces are made-to-match, but cannot be “exact” matches. The stair nose pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces

Production time for this material is approximately 10 business days.

  • Color: Made-to-order and match as best as possible
    to your selected product
  • Size: 5/8″ Thick x 96″ Long x 3-1/4″ Deep
  • Material: Solid White European Oak Stair Nose
  • Installation: Glue Down with Tongue and Groove
  • Profile: 7/8″ thick Square Edge with lightly smoothed edges
  • 1-1/8″ Stair Nose Overhang

Some custom work will be accepted on a per request basis.


SOLID STAIR NOSE – ROUNDED BULLNOSE

Stair Nose Molding are used to cap each hardwood step professionally. Please note that the stair nose pieces are made-to-match, but cannot be “exact” matches. The stair nose pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces

Production time for this material is approximately 10 business days.

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 5/8″ Thick x 96″ Long x 3-1/2″ Deep
  • Material: Solid White European Oak Stair Nose
  • Installation: Glue Down with Tongue and Groove
  • Profile: 7/8″ thick Bullnose (rounded)
  • 1-3/8″ Stair Nose Overhang

Some custom work will be accepted on a per request basis.


SOLID RISER – SQUARE EDGE

Our Vertical Stair Stair Way Risers allow for improved weight support between each stair.Please note that stair riser pieces are made-to-match, but cannot be “exact” matches. The stair riser pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces
Production time for this material is approximately 10 business days

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 3/4″ Thick x 96″ Long x 7-1/2″ Tall
  • Material: Solid White European Oak Stair Tread
  • Installation: Glue Down
  • Profile: Square Edge Solid One-piece Riser
  • Finish: Top and Square Edge Left or Right Faces are Finished – All other sides are unfinished

Some custom work will be accepted on a per request basis.


REDUCER

Our Reducer allows connection and transition of two rooms with different floor heights. The reducer combines style and function for a professionally beautiful and functional flooring transition. The reducer also provides the proper connection between height of flooring in one room to the other, such as under the door frame moving from balcony to living room. Please note that reducer pieces are made-to-match, but cannot be “exact” matches. The reducer pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces
Production time for this material is approximately 10 business days

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 5/8″ Thick x 96″ Long x 2″ Wide
  • Material: Solid White European Oak Reducer
  • Installation: Glue Down
  • Profile: Flush Rounded Visible Transition

Some custom work will be accepted on a per request basis.


QUARTER ROUND

Quarter Round connects and transitions walls and floors professionally. Please note that quarter round pieces are made-to-match, but cannot be “exact” matches. The quarter round pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces
Production time for this material is approximately 10 business days

  • Color: Made-to-order and match as best as possible
    to selected product
  • Size: 3/4″ Tall x 96″ Long x 3/4″ Wide
  • Material: Solid White European Oak Quarter Round
  • Installation: Glue Down
  • Profile: Rounded Visible Transition

Some custom work will be accepted on a per request basis.


END CAP

Our End Cap is used to conceal end cuts and to border off where a floor ends, such as at a doorway or two rooms with different floor heights. The end cap also provides the proper connection between one rooms flooring height to the next, as well as where the floors meets walls. Please note that reducer pieces are made-to-match, but cannot be “exact” matches. The end cap pieces are stained with a custom blend and then sealed for a factory-like finish. Wood has natural variation and grain that prevents a perfect match, however, we will make the custom stain blend as close as possible to complement the purchased flooring and assist with finishing your new hardwood installation.

Sold Per 8 ft. Pieces
Production time for this material is approximately 10 business days

  • Color: Made-to-order and match as best as possible to selected product
  • Size: 5/8″ Thick x 96″ Long x 1-1/2″ Wide
  • Material: Solid White European Oak End Cap
  • Installation: Glue Down or Float
  • Profile: Flush Rounded Visible Transition

Some custom work will be accepted on a per request basis.

Click Here to Request a Sample of our Wood Flooring.